Ametek ReFlex Programming Manual Manuel d'utilisateur Page 85
- Page / 134
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
DC Module Remote Programming ReFlex Power™ Programming Manual
M380056-03 Rev L 81
3.14
TRIGGER SCPI COMMANDS
The SCPI commands associated with establishing external trigger signals are
listed in this section.
3.14.1
TRIGGER
SCPI
C
OMMAND
S
UMMARY
TRIGger<n>
:DISPlay?
:INP <t>
:OUTP <t>
:INP <t>, OUTP <t>
:OUTP <t>, INP <t>
:INPut:SLOPe [POSitive | NEGative | BOTH | NONE
1
]
:OUTput:SLOPe [POSitive | NEGative | BOTH]
:TRIG <t>
:WIDTh<+NRf>
3.14.2
T
RIGGER
SCPI
C
OMMAND
R
EFERENCE
Command
Description
TRIGger<n>
Trigger subsystem. <n> = module number.
:DISPlay?
Displays the module’s usage of the GPIO Buss signals,
that are used in the currently loaded List. See LIST below.
:
INP <t>
Establish that on module n, trigger t is an input. t = a-d, fa
(front panel only, in the DC module). (Non-pass through
mode.)
:
OUTP <t>
Establish that on module n, trigger t is an output. t = a-d,
fa. (Non-pass through mode.)
:
INP <t>, OUTP <t>
:
OUTP <t>, INP <t>
The RFP’s GPIO Buss signals (t = a, b, c, or d) connected
to ‘fa’, the Modules Front Panel trigger, specifying
direction. The trigger signal is passed through the Module.
:
INPut:SLOPe [POSitive |
NEGative | BOTH | NONE
1
]
Sets module n’s fa trigger input edge as positive, negative,
or both.
:
OUTPut:SLOPe [POSitive |
NEGative | BOTH]
Sets module n’s fa trigger output edge as positive,
negative, or both.
:
TRIG<t>
2
Generate a trigger from module n, t = a-d, fa.
:
WIDTh<+NRf>
n = Module number, sets Front Panel trigger output pulse
width in SLOPE POS / NEG mode. The WIDTh timing
range is 2.0e-6 to 2.097 seconds.
Note: At this time the ReFlex Power™ system only implements direct trigger mapping
‘a’ to ‘fa’, ‘b’ to ‘fb’, ‘c’ to ‘fc’ and ‘d’ to ‘fd.’
1
The
TRIG:SLOPe NONE
parameter disables the trigger and disconnects the ‘fx’ to ‘x’
connection.
2
The POSitive and NEGative trigger pulse’s on the Front Panel trigger output are not
retriggerable, if a trigger pulse is being produced, and another trigger out is
executed, it will be ignored, and no errors will be posted.
- ReFlex Power™ 1
- (“AMETEK”): 5
- SAFETY SYMBOLS 7
- CONTENTS 11
- LIST OF TABLES 17
- LIST OF FIGURES 18
- REMOTE PROGRAMMING OVERVIEW 19
- 1.4.1 F 21
- 18 M380056-03 Rev M 22
- CONTROLLER MODULE REMOTE 23
- CONFIGURATION 24
- THERNET 25
- ROCEDURE 25
- 2.4.3 L 26
- M380056-03 Rev L 23 27
- 2.5.1 H 28
- 2.5.2 LOGIN 29
- 2.5.3 IP 30
- 28 M380056-03 Rev M 32
- 2.5.4 S 33
- 2.5.5 M 36
- Figure 2-13. Net Test Window 37
- 2.6.1 M 39
- SCPI COMMAND OPERATION 40
- 2.8.4 Q 43
- EIB SCPI COMMANDS 45
- SYSTEM:NETWORK SCPI COMMANDS 46
- 2.11.2 SYSTEM:NETWORK 47
- RFP SERVICE REQUEST 48
- XECUTION TIME 50
- PERATION 50
- RELATED 51
- 48 M380056-03 Rev M 52
- ETTING THE 53
- BIT IN THE 53
- AN EXAMPLE 53
- TRIGGER SCPI COMMANDS 54
- MEMORY SCPI COMMANDS 55
- 52 M380056-03 Rev M 56
- DC MODULE REMOTE PROGRAMMING 57
- :LOCK 62
- 3.9.2 SOURCE 67
- XTERNAL 72
- RIGGERING 72
- SCPI Command Description 74
- ‘fa’, ‘b’ to ‘fb’… 74
- 72 M380056-03 Rev M 76
- Figure 3-8. List Mode Logic 78
- 78 M380056-03 Rev M 82
- LIST SCPI COMMANDS 86
- 84 M380056-03 Rev M 88
- DC SYSTEM SCPI COMMANDS 89
- 88 M380056-03 Rev M 92
- AC MODULE REMOTE PROGRAMMING 93
- 4.4.2 E 96
- 4.6.2 CALIBRATION 100
- MEASURE SCPI COMMANDS 103
- OUTPUT SCPI COMMANDS 104
- SOURCE SCPI COMMANDS 105
- EFERENCE 106
- cross waveform 107
- STATUS SCPI COMMANDS 110
- M380056-03 Rev L 107 111
- SYSTEM SCPI COMMANDS 112
- PARALLEL GROUPS 112
- 4.12.2 E 113
- 110 M380056-03 Rev L 114
- LOAD MODULE REMOTE 115
- PROGRAMMING 115
- POWER-ON CONDITIONS 116
- ERROR CODES 117
- COMMON SCPI COMMANDS 118
- CALIBRATION SCPI COMMANDS 119
- 5.6.2 CALIBRATION 120
- INPUT SCPI COMMANDS 122
- FIXED POWER DC REMOTE 127
- 6.5.2 CALIBRATION 131
- STATUS COMMANDS 133
- SYSTEM COMMANDS 133
- 130 M380056-03 Rev L 134
Produits connexes et manuels pour Équipement Ametek ReFlex Programming Manual
Équipement Ametek ReFlex Manuel d'utilisateur
(359 pages)
(359 pages)
Équipement Ametek SLM-1 Manuel d'utilisateur
(77 pages)
(77 pages)
Équipement Ametek SLM-4 Manuel d'utilisateur
(77 pages)
(77 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels