Ametek ReFlex Programming Manual Manuel d'utilisateur Page 65
- Page / 134
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
DC Module Remote Programming ReFlex Power™ Programming Manual
M380056-03 Rev L 61
will be generated. The default Polarity will be Normal with the
Positive Output on Out 1.
:POLarity?
Query the state of the polarity relay.
:PROTection
:DELAY <NRf>
Set Shutdown delay timer value, 0 to 40.95 Seconds
:DELAY?
Query Shutdown delay timer value
:FOLD <NRi>
Shutdown Mode, 0= Normal CC/CV mode operation.
1= Fault if Supply switches into Voltage mode.
2= Fault if Supply switches into Constant Current mode.
:FOLD?
Query Shutdown Mode setting.
:STATe <bool>
Closes the isolation/sense relays. Sets the output voltage and
current to programmed values, turns on the supply. Valid
arguments are 1/ON or 0/OFF. *RST state value is OFF.
CAUTION: Ensure that suitable delays are incorporated to
preclude hot switching of the isolation relay. See :DEFault
keyword entry for automatic relay operation..
:STATe?
Query the state of the unit. 1 means unit is on and 0 means unit
is off
:SENSe <bool>
Turns On/Off the output Sense relay. The output ISOL relay
must be closed to close the Sense relay. Valid arguments are
1/ON or 0/OFF.
:SENSe?
Query the state of output SENSe relay.
:DEFault <bool>
Sets DEFault state of SENSe Relay, POR default state is ON.
The ISOL/SENSe relays will be automatically sequenced during
the STATE command.
:DEFault?
Query DEFault state of SENSe Relay.
:TRIPped?
Returns the integer value 1 (TRIPPED) or 0 (UNTRIPPED) state
of the output.
:MODFault <bool>
When 1/ON, sets Module Trigger Out to assert HIGH when a
HW fault is detected. 0/OFF returns Trigger out to normal
operation.
Used
to enable / disable
Fault Group operation.
:MODFault?
Query the state of Module Fault Mode
:CLEar <bool>
When in Module Fault mode, 1/ON, forces Trigger out to LOW to
allow a Fault Group to be cleared.
:CLEar?
Query if the state of the Module Fault output is forced LOW.
:
DPDelay
Down Programmer turn off delay timer (maximum ON time)
:TIMER
<NRf>
Programs the down programmer to be ON for a maximum of 0.1
to 60.0 seconds. Programming 0 seconds (Default setting)
disables the timer, and the down programmer is always enabled
.
If the timer counts down and expires, the down programmer will
be turned OFF. The timer starts when the down programmer
needs to sink current to keep the supply output in regulation.
The programmed value is automatically saved. It is not cleared
by *RST. SYST:ERR?:- ELGAR_NOT_ SUPPORTED is
returned if the feature is not implemented.
:TIMER?
Returns the setting for the delay timer. If 0.0 is returned, the max
on delay timer is disabled, and then down programmer enabled.
This is the default operating mode. If the feature is not
implemented ELGAR_NOT_SUPPORTED is returned.
- ReFlex Power™ 1
- (“AMETEK”): 5
- SAFETY SYMBOLS 7
- CONTENTS 11
- LIST OF TABLES 17
- LIST OF FIGURES 18
- REMOTE PROGRAMMING OVERVIEW 19
- 1.4.1 F 21
- 18 M380056-03 Rev M 22
- CONTROLLER MODULE REMOTE 23
- CONFIGURATION 24
- THERNET 25
- ROCEDURE 25
- 2.4.3 L 26
- M380056-03 Rev L 23 27
- 2.5.1 H 28
- 2.5.2 LOGIN 29
- 2.5.3 IP 30
- 28 M380056-03 Rev M 32
- 2.5.4 S 33
- 2.5.5 M 36
- Figure 2-13. Net Test Window 37
- 2.6.1 M 39
- SCPI COMMAND OPERATION 40
- 2.8.4 Q 43
- EIB SCPI COMMANDS 45
- SYSTEM:NETWORK SCPI COMMANDS 46
- 2.11.2 SYSTEM:NETWORK 47
- RFP SERVICE REQUEST 48
- XECUTION TIME 50
- PERATION 50
- RELATED 51
- 48 M380056-03 Rev M 52
- ETTING THE 53
- BIT IN THE 53
- AN EXAMPLE 53
- TRIGGER SCPI COMMANDS 54
- MEMORY SCPI COMMANDS 55
- 52 M380056-03 Rev M 56
- DC MODULE REMOTE PROGRAMMING 57
- :LOCK 62
- 3.9.2 SOURCE 67
- XTERNAL 72
- RIGGERING 72
- SCPI Command Description 74
- ‘fa’, ‘b’ to ‘fb’… 74
- 72 M380056-03 Rev M 76
- Figure 3-8. List Mode Logic 78
- 78 M380056-03 Rev M 82
- LIST SCPI COMMANDS 86
- 84 M380056-03 Rev M 88
- DC SYSTEM SCPI COMMANDS 89
- 88 M380056-03 Rev M 92
- AC MODULE REMOTE PROGRAMMING 93
- 4.4.2 E 96
- 4.6.2 CALIBRATION 100
- MEASURE SCPI COMMANDS 103
- OUTPUT SCPI COMMANDS 104
- SOURCE SCPI COMMANDS 105
- EFERENCE 106
- cross waveform 107
- STATUS SCPI COMMANDS 110
- M380056-03 Rev L 107 111
- SYSTEM SCPI COMMANDS 112
- PARALLEL GROUPS 112
- 4.12.2 E 113
- 110 M380056-03 Rev L 114
- LOAD MODULE REMOTE 115
- PROGRAMMING 115
- POWER-ON CONDITIONS 116
- ERROR CODES 117
- COMMON SCPI COMMANDS 118
- CALIBRATION SCPI COMMANDS 119
- 5.6.2 CALIBRATION 120
- INPUT SCPI COMMANDS 122
- FIXED POWER DC REMOTE 127
- 6.5.2 CALIBRATION 131
- STATUS COMMANDS 133
- SYSTEM COMMANDS 133
- 130 M380056-03 Rev L 134
Produits connexes et manuels pour Équipement Ametek ReFlex Programming Manual
Équipement Ametek ReFlex Manuel d'utilisateur
(359 pages)
(359 pages)
Équipement Ametek SLM-1 Manuel d'utilisateur
(77 pages)
(77 pages)
Équipement Ametek SLM-4 Manuel d'utilisateur
(77 pages)
(77 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels