Ametek ReFlex Programming Manual Manuel d'utilisateur Page 62
- Page / 134
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ReFlex Power™ Programming Manual DC Module Remote Programming
58 M380056-03 Rev M
:LOCK
:STORe
:UNLock <string>
:REVERT:FACTory
3.6.2 CALIBRATION
SCPI
C
OMMAND
R
EFERENCE
Command
Description
CALibrate<n>
Calibration subsystem. Module ‘n’.
:INITial
:CURRent
[:AMPLitude] <NRf>
Sets the power-on default value of current.
[:AMPLitude]?
Query the power-on default value of current
:PROTection <NRf>
Sets the power-on default value of the over current
protection.
:PROTection?
Query the power-on default value of the over current
protection.
:VOLTage
[:AMPLitude] <NRf>
Sets the power-on default voltage. Should be set to zero
volts to avoid hot switching of output relay.
[:AMPLitude]?
Query the power-on default voltage. Should be set to zero
volts to avoid hot switching of output relay.
:PROTection <NRf>
Sets the power-on default value of the over voltage
protection.
:PROTection?
Query the power-on default value of the over voltage
protection.
:STATe <bool>
1
Set the initial POR output state of the unit
:STATe?
Query the initial POR output state setting of the unit
:UNDERVOLTage
:PROTection <NRf>
Sets the power-on default value of the under voltage
protection.
:PROTection?
Query the power-on default value of the under voltage
protection.
:DEFAult
Sets initial settings to Factory defaults of 0.0
Volts/Amps/UVP, OVP/OCP to Module Max values and
POR State to Off.
:OUTPut
:CURRent
:COUNTS <NRi>
Set Current DAC
setpoint, in counts
:FIVEPOINT<1-5> <0+NRf>
Sets the current output calibration point (1 through 5). The
actual output current is measured with an external meter.
:FIVEPOINT?
Returns 5 pairs of current calibration setpoint count and
related current values
:PROTection
:COUNTS <NRi>
Set Protection value 0-4095
:VOLTage
:COUNTS <NRi>
Set Voltage DAC setpoint, in counts
:FIVEPOINT<1-5> <NRf>
Sets the voltage output calibration point (1 through 5). The
actual output voltage is measured with an external meter.
- ReFlex Power™ 1
- (“AMETEK”): 5
- SAFETY SYMBOLS 7
- CONTENTS 11
- LIST OF TABLES 17
- LIST OF FIGURES 18
- REMOTE PROGRAMMING OVERVIEW 19
- 1.4.1 F 21
- 18 M380056-03 Rev M 22
- CONTROLLER MODULE REMOTE 23
- CONFIGURATION 24
- THERNET 25
- ROCEDURE 25
- 2.4.3 L 26
- M380056-03 Rev L 23 27
- 2.5.1 H 28
- 2.5.2 LOGIN 29
- 2.5.3 IP 30
- 28 M380056-03 Rev M 32
- 2.5.4 S 33
- 2.5.5 M 36
- Figure 2-13. Net Test Window 37
- 2.6.1 M 39
- SCPI COMMAND OPERATION 40
- 2.8.4 Q 43
- EIB SCPI COMMANDS 45
- SYSTEM:NETWORK SCPI COMMANDS 46
- 2.11.2 SYSTEM:NETWORK 47
- RFP SERVICE REQUEST 48
- XECUTION TIME 50
- PERATION 50
- RELATED 51
- 48 M380056-03 Rev M 52
- ETTING THE 53
- BIT IN THE 53
- AN EXAMPLE 53
- TRIGGER SCPI COMMANDS 54
- MEMORY SCPI COMMANDS 55
- 52 M380056-03 Rev M 56
- DC MODULE REMOTE PROGRAMMING 57
- :LOCK 62
- 3.9.2 SOURCE 67
- XTERNAL 72
- RIGGERING 72
- SCPI Command Description 74
- ‘fa’, ‘b’ to ‘fb’… 74
- 72 M380056-03 Rev M 76
- Figure 3-8. List Mode Logic 78
- 78 M380056-03 Rev M 82
- LIST SCPI COMMANDS 86
- 84 M380056-03 Rev M 88
- DC SYSTEM SCPI COMMANDS 89
- 88 M380056-03 Rev M 92
- AC MODULE REMOTE PROGRAMMING 93
- 4.4.2 E 96
- 4.6.2 CALIBRATION 100
- MEASURE SCPI COMMANDS 103
- OUTPUT SCPI COMMANDS 104
- SOURCE SCPI COMMANDS 105
- EFERENCE 106
- cross waveform 107
- STATUS SCPI COMMANDS 110
- M380056-03 Rev L 107 111
- SYSTEM SCPI COMMANDS 112
- PARALLEL GROUPS 112
- 4.12.2 E 113
- 110 M380056-03 Rev L 114
- LOAD MODULE REMOTE 115
- PROGRAMMING 115
- POWER-ON CONDITIONS 116
- ERROR CODES 117
- COMMON SCPI COMMANDS 118
- CALIBRATION SCPI COMMANDS 119
- 5.6.2 CALIBRATION 120
- INPUT SCPI COMMANDS 122
- FIXED POWER DC REMOTE 127
- 6.5.2 CALIBRATION 131
- STATUS COMMANDS 133
- SYSTEM COMMANDS 133
- 130 M380056-03 Rev L 134
Produits connexes et manuels pour Équipement Ametek ReFlex Programming Manual
Équipement Ametek ReFlex Manuel d'utilisateur
(359 pages)
(359 pages)
Équipement Ametek SLM-1 Manuel d'utilisateur
(77 pages)
(77 pages)
Équipement Ametek SLM-4 Manuel d'utilisateur
(77 pages)
(77 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels