Ametek SFA Series Ethernet Programming Manuel d'utilisateur Page 14
- Page / 159
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Contents SG Series Programming
xvi M550129-03 Rev K
6.3.1 Parameter Definitions ....................................................................... 6-8
6.3.2 Units ................................................................................................. 6-9
6.3.3 Conventions...................................................................................... 6-9
6.3.4 Queries ............................................................................................. 6-9
6.4 IEEE 488.2 Common Command Subsystem ................................................ 6-10
6.5 SOURCE SCPI Command Subsystem ......................................................... 6-12
6.5.1 SOURCE SCPI Command Summary.............................................. 6-12
6.5.2 SOURCE SCPI Command Reference ............................................ 6-13
6.5.3 RAMP FUNCTION .......................................................................... 6-16
6.6 MEASURE SCPI Command Subsystem ....................................................... 6-17
6.6.1 MEASURE SCPI Command Summary ........................................... 6-17
6.6.2 MEASURE SCPI Command Reference .......................................... 6-17
6.7 OUTPUT SCPI Command Subsystem .......................................................... 6-18
6.7.1 OUTPUT SCPI Command Summary .............................................. 6-18
6.7.2 OUTPUT SCPI Command Reference ............................................. 6-18
6.8 STATUS SCPI Command Subsystem .......................................................... 6-19
6.8.1 STATUS SCPI Command Summary ............................................... 6-19
6.8.2 STATUS SCPI Command Reference .............................................. 6-20
6.9 SYSTEM SCPI Command Subsystem .......................................................... 6-21
6.9.1 SYSTEM SCPI Command Summary .............................................. 6-21
6.9.2 SYSTEM SCPI Command Reference ............................................. 6-22
6.10 HTRIGGER SCPI Command Subsystem ..................................................... 6-25
6.10.1 HTRIGGER SCPI Command Summary .......................................... 6-25
6.10.2 HTRIGGER SCPI Command Reference ......................................... 6-25
6.11 TRIGGER SCPI Command Subsystem ........................................................ 6-26
6.11.1 TRIGGER SCPI Command Summary ............................................. 6-26
6.11.2 TRIGGER SCPI Command Reference ........................................... 6-26
6.12 CALIBRATION SCPI Command Subsystem ................................................. 6-27
6.12.1 CALIBRATION SCPI Command Summary ..................................... 6-27
6.12.2 CALIBRATION SCPI Command Reference .................................... 6-29
6.13 SGI-Unique Commands ................................................................................ 6-32
6.13.1 Restrictions on Sequence Programming: ........................................ 6-32
6.13.2 SGI SOURCE SCPI Command Subsystem .................................... 6-34
6.13.3 SGI PROGRAM SCPI Command Subsystem ................................. 6-35
6.13.4 SGI MEASURE SCPI Command Subsystem .................................. 6-42
6.13.5 SGI HTRIGGER SCPI Command Subsystem ................................. 6-42
6.14 Examples of Using the SCPI Commands ..................................................... 6-43
6.14.1 VI Mode Example ........................................................................... 6-43
6.14.2 OVP Setup Example ....................................................................... 6-43
6.14.3 Trigger Example ............................................................................. 6-44
6.14.4 Hardware Trigger Example ............................................................. 6-45
6.14.5 Ramp V Example ............................................................................ 6-45
6.14.6 Ramp I Example ............................................................................. 6-45
- SG Series IEEE 1
- 488.2/RS232 and 1
- Ethernet Options 1
- CONTENTS 12
- OVERVIEW 19
- M550129-03 Rev 20
- IEEE 488.2 GPIB/RS232 21
- FEATURES, FUNCTIONS 21
- AND SPECIFICATIONS 21
- READBACK FUNCTIONS 22
- SPECIFICATIONS 22
- IEEE 488.2 GPIB/ RS232 23
- CONFIGURATIONS 23
- AND REMOTE PROGRAMMING 23
- RS232 SETUP PROCEDURE 25
- Configuration Switch 27
- Remote/Local Selection 28
- Shield Ground 30
- Address Selection 30
- REMOTE PROGRAMMING VIA RS232 31
- ETHERNET INTERFACE 33
- FEATURES, FUNCTIONS AND 33
- FEATURES AND FUNCTIONS 34
- Programming Resolution 36
- Programming Accuracy 36
- Readback Resolution 36
- Readback Accuracy 37
- ETHERNET CONFIGURATION 41
- AND REMOTE PROGRAMMING 41
- ETHERNET SETUP PROCEDURE 43
- Network Setup Using DHCP 44
- Network Setup Using Auto-IP 45
- EXTERNAL USER CONTROL SIGNAL 50
- CONNECTOR 50
- ETHERNET 53
- ETHERNET WEB PAGES, OVERVIEW 54
- Figure 5-11. Login Window 55
- CONFIGURATION 56
- IP CONFIGURATION 57
- SETTINGS 61
- PRESETS 68
- SECURITY 70
- EXISTING 72
- AND SCPI COMMAND OPERATION 73
- Register 75
- Registers 77
- Error/Event Queue 77
- CONFORMANCE INFORMATION 80
- Conventions 81
- Queries 81
- IEEE 488.2 COMMON COMMAND 82
- SUBSYSTEM 82
- SOURCE SCPI Command Summary 84
- RAMP FUNCTION 88
- MEASURE SCPI Command Summary 89
- OUTPUT SCPI Command Summary 90
- STATUS SCPI Command Summary 91
- SYSTEM SCPI Command Summary 93
- TRIGGER SCPI Command Summary 98
- (applies to Ethernet only) 100
- SGI-UNIQUE COMMANDS 104
- M550129-03 Rev K 105
- EFERENCE 108
- VI Mode Example 115
- OVP Setup Example 115
- Trigger Example 116
- Hardware Trigger Example 117
- Ramp V Example 117
- Ramp I Example 117
- Ramp V Example 2 118
- Power On INIT Example 118
- “Charge” 128
- “Discharge” 128
- CALIBRATION 135
- SETUP FOR CALIBRATION 136
- (ETHERNET) 137
- (ETHERNET, GPIB) 139
- CALIBRATION (ETHERNET, GPIB) 140
- CAL:OUTP:CURR:CALC 144
- ANALOG PROGRAM ADJUSTMENT 145
- Adjustment for Current Mode 148
- Adjustment for Voltage Mode 149
- SCPI STATUS IMPLEMENTATION 153
Produits connexes et manuels pour Équipement Ametek SFA Series Ethernet Programming
Équipement Ametek SLM-1 Manuel d'utilisateur
(77 pages)
(77 pages)
Équipement Ametek SLM-4 Manuel d'utilisateur
(77 pages)
(77 pages)
(185 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels