Ametek SFA Series Ethernet Programming Manuel d'utilisateur Page 116
- Page / 159
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SCPI Command Operation SG Series Programming
6-44 M550129-03 Rev K
*CLS // clear the unit to its power-on default settings.
*RST // reset the unit.
SOUR:VOLT:PROT 4.0 // program the OVP trip point to 4.0 VDC.
SOUR:VOLT:PROT? // confirm the OVP trip point setting (response: 4.0).
SOUR:CURR 1.0 // program output current to 1.0 A.
SOUR:VOLT 3.0 // program output voltage to 3.0 VDC.
STAT:PROT:ENABLE 8 // program the unit to report OVP trip.
STAT:PROT:ENABLE? // confirm that OVP fault is enabled (response: 8).
*SRE 2 // enable the GPIB service request upon a fault.
*SRE? // confirm the GPIB service request enabled (response 2).
STAT:PROT:EVENT? // confirm no faults occurred (response: 0).
// confirm that the OVP led and SRQ led is not active.
SOUR:VOLT 7.0 // program output voltage to 7.0 VDC - cause OVP trip!
// confirm that unit issued a GPIB service request (use a serial
poll).
6.14.3
Trigger Example
Program a unit with no load at the output to change its output voltage and
current to 5 VDC @ 1A at the same time.
// Use SYST:ERR? after each command to verify no programming errors.
// turn on the unit.
*CLS // clear the unit to its power-on default settings.
*RST // reset the unit.
SOUR:CURR:TRIG 1.0 // program output current to 1.0 A upon trigger.
SOUR:CURR:TRIG? // confirm output current set to 1.0 A upon trigger.
SOUR:VOLT:TRIG 5.0 // program output voltage to 5.0 VDC upon trigger
SOUR:VOLT:TRIG? // confirm output current set to 5.0 VDC upon trigger.
MEAS:CURR? // measure the actual output current (response: 0.0).
MEAS:VOLT? // measure the actual output voltage (response: 0.0).
TRIG:TYPE 3 // trigger the unit to implement curr and volt programming.
MEAS:CURR? // measure the actual output current (response: ~ 0. 0 with no
load on output).
MEAS:VOLT? // measure the actual output voltage (response: ~ 5.0).
TRIG:ABORT // turn off trigger mode.
- SG Series IEEE 1
- 488.2/RS232 and 1
- Ethernet Options 1
- CONTENTS 12
- OVERVIEW 19
- M550129-03 Rev 20
- IEEE 488.2 GPIB/RS232 21
- FEATURES, FUNCTIONS 21
- AND SPECIFICATIONS 21
- READBACK FUNCTIONS 22
- SPECIFICATIONS 22
- IEEE 488.2 GPIB/ RS232 23
- CONFIGURATIONS 23
- AND REMOTE PROGRAMMING 23
- RS232 SETUP PROCEDURE 25
- Configuration Switch 27
- Remote/Local Selection 28
- Shield Ground 30
- Address Selection 30
- REMOTE PROGRAMMING VIA RS232 31
- ETHERNET INTERFACE 33
- FEATURES, FUNCTIONS AND 33
- FEATURES AND FUNCTIONS 34
- Programming Resolution 36
- Programming Accuracy 36
- Readback Resolution 36
- Readback Accuracy 37
- ETHERNET CONFIGURATION 41
- AND REMOTE PROGRAMMING 41
- ETHERNET SETUP PROCEDURE 43
- Network Setup Using DHCP 44
- Network Setup Using Auto-IP 45
- EXTERNAL USER CONTROL SIGNAL 50
- CONNECTOR 50
- ETHERNET 53
- ETHERNET WEB PAGES, OVERVIEW 54
- Figure 5-11. Login Window 55
- CONFIGURATION 56
- IP CONFIGURATION 57
- SETTINGS 61
- PRESETS 68
- SECURITY 70
- EXISTING 72
- AND SCPI COMMAND OPERATION 73
- Register 75
- Registers 77
- Error/Event Queue 77
- CONFORMANCE INFORMATION 80
- Conventions 81
- Queries 81
- IEEE 488.2 COMMON COMMAND 82
- SUBSYSTEM 82
- SOURCE SCPI Command Summary 84
- RAMP FUNCTION 88
- MEASURE SCPI Command Summary 89
- OUTPUT SCPI Command Summary 90
- STATUS SCPI Command Summary 91
- SYSTEM SCPI Command Summary 93
- TRIGGER SCPI Command Summary 98
- (applies to Ethernet only) 100
- SGI-UNIQUE COMMANDS 104
- M550129-03 Rev K 105
- EFERENCE 108
- VI Mode Example 115
- OVP Setup Example 115
- Trigger Example 116
- Hardware Trigger Example 117
- Ramp V Example 117
- Ramp I Example 117
- Ramp V Example 2 118
- Power On INIT Example 118
- “Charge” 128
- “Discharge” 128
- CALIBRATION 135
- SETUP FOR CALIBRATION 136
- (ETHERNET) 137
- (ETHERNET, GPIB) 139
- CALIBRATION (ETHERNET, GPIB) 140
- CAL:OUTP:CURR:CALC 144
- ANALOG PROGRAM ADJUSTMENT 145
- Adjustment for Current Mode 148
- Adjustment for Voltage Mode 149
- SCPI STATUS IMPLEMENTATION 153
Produits connexes et manuels pour Équipement Ametek SFA Series Ethernet Programming
Équipement Ametek SLM-1 Manuel d'utilisateur
(77 pages)
(77 pages)
Équipement Ametek SLM-4 Manuel d'utilisateur
(77 pages)
(77 pages)
(185 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels