Ametek SFA Series Ethernet Programming Manuel d'utilisateur Page 115
- Page / 159
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SG Series Programming SCPI Command Operation
M550129-03 Rev K
6-43
Command
Description
SCPI
:ARM
<boolean>
Readies the last loaded sequence to run when the external Hardware
Trigger signal is issued.
1 = Ready to run sequence when Hardware trigger is engaged.
0 = Not Armed, Hardware trigger is ignored
NOTE: To arm a different sequence, issue the HTRIG:SEQ
command first.
N
:ARM?
Returns the ready status of the last loaded sequence.
1 = Ready to run sequence when Hardware trigger is engaged.
0 = Not Armed, Hardware trigger is ignored
NOTE: To load a new sequence to be armed you must issue the
HTRIG:SEQ command first.
N
6.14
EXAMPLES OF USING THE SCPI COMMANDS
The following examples demonstrate programming a power supply to
control and to readback the output using the SCPI commands. The
maximum voltage and current output is dependent on the particular model.
The examples list only the SCPI commands; the code required to send the
commands is dependent on the type of language you are using (e.g., C or
BASIC) and GPIB hardware (e.g., National Instruments).
6.14.1
VI Mode Example
Program a unit with no load at the output to 5 VDC @ 1A, and verify the
output.
// Use SYST:ERR? after each command to verify no programming errors.
// turn on the unit.
*CLS // clear the unit to its power-on default settings.
*RST // reset the unit.
SOUR:CURR 1.0 // program output current to 1.0 A.
SOUR:CURR? // confirm the output current setting (response: 1.0).
SOUR:VOLT 5.0 // program output voltage to 5.0 VDC.
SOUR:VOLT? // confirm the output voltage setting (response: 5.0).
MEAS:CURR? // measure the actual output current (response: ~ 0.0 with no load
on output).
MEAS:VOLT? // measure the actual output voltage (response: ~ 5.0).
6.14.2
OVP Setup Example
Program a unit with no load at the output to generate a GPIB service
request upon an overvoltage protection trip condition. (Must use GPIB
not RS232.)
// Use SYST:ERR? after each command to verify no programming errors.
// assure that PON is not selected on the rear panel switch.
// Turn on the unit.
- SG Series IEEE 1
- 488.2/RS232 and 1
- Ethernet Options 1
- CONTENTS 12
- OVERVIEW 19
- M550129-03 Rev 20
- IEEE 488.2 GPIB/RS232 21
- FEATURES, FUNCTIONS 21
- AND SPECIFICATIONS 21
- READBACK FUNCTIONS 22
- SPECIFICATIONS 22
- IEEE 488.2 GPIB/ RS232 23
- CONFIGURATIONS 23
- AND REMOTE PROGRAMMING 23
- RS232 SETUP PROCEDURE 25
- Configuration Switch 27
- Remote/Local Selection 28
- Shield Ground 30
- Address Selection 30
- REMOTE PROGRAMMING VIA RS232 31
- ETHERNET INTERFACE 33
- FEATURES, FUNCTIONS AND 33
- FEATURES AND FUNCTIONS 34
- Programming Resolution 36
- Programming Accuracy 36
- Readback Resolution 36
- Readback Accuracy 37
- ETHERNET CONFIGURATION 41
- AND REMOTE PROGRAMMING 41
- ETHERNET SETUP PROCEDURE 43
- Network Setup Using DHCP 44
- Network Setup Using Auto-IP 45
- EXTERNAL USER CONTROL SIGNAL 50
- CONNECTOR 50
- ETHERNET 53
- ETHERNET WEB PAGES, OVERVIEW 54
- Figure 5-11. Login Window 55
- CONFIGURATION 56
- IP CONFIGURATION 57
- SETTINGS 61
- PRESETS 68
- SECURITY 70
- EXISTING 72
- AND SCPI COMMAND OPERATION 73
- Register 75
- Registers 77
- Error/Event Queue 77
- CONFORMANCE INFORMATION 80
- Conventions 81
- Queries 81
- IEEE 488.2 COMMON COMMAND 82
- SUBSYSTEM 82
- SOURCE SCPI Command Summary 84
- RAMP FUNCTION 88
- MEASURE SCPI Command Summary 89
- OUTPUT SCPI Command Summary 90
- STATUS SCPI Command Summary 91
- SYSTEM SCPI Command Summary 93
- TRIGGER SCPI Command Summary 98
- (applies to Ethernet only) 100
- SGI-UNIQUE COMMANDS 104
- M550129-03 Rev K 105
- EFERENCE 108
- VI Mode Example 115
- OVP Setup Example 115
- Trigger Example 116
- Hardware Trigger Example 117
- Ramp V Example 117
- Ramp I Example 117
- Ramp V Example 2 118
- Power On INIT Example 118
- “Charge” 128
- “Discharge” 128
- CALIBRATION 135
- SETUP FOR CALIBRATION 136
- (ETHERNET) 137
- (ETHERNET, GPIB) 139
- CALIBRATION (ETHERNET, GPIB) 140
- CAL:OUTP:CURR:CALC 144
- ANALOG PROGRAM ADJUSTMENT 145
- Adjustment for Current Mode 148
- Adjustment for Voltage Mode 149
- SCPI STATUS IMPLEMENTATION 153
Produits connexes et manuels pour Équipement Ametek SFA Series Ethernet Programming
Équipement Ametek SLM-1 Manuel d'utilisateur
(77 pages)
(77 pages)
Équipement Ametek SLM-4 Manuel d'utilisateur
(77 pages)
(77 pages)
(185 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels