Ametek Lx Series II Programming Manual Manuel d'utilisateur Page 37
- Page / 242
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Programming Manual Lx \ Ls Series II
33
3.4 RS232C Serial Interface
The RS232C interface has been retained on the Lx/Ls Series II power source models for
backward compatibility with the Series I products. It functions exactly like it did on the first
generation products.
Note: If a USB cable is plugged into the USB interface connector of the power source, the RS232
interface will be disabled. Remove any USB connection to use the serial port.
The RS232C interface is factory enabled for all Lx/Ls models, except those ordered with the
optional –LAN interface. Models with the –LAN option have the LAN interface enabled and the
RS232C port disabled.
Note: If the –LAN option is installed, jumper W2 on the range/relay board (Assy P/N 7004-716-1)
must be installed. This jumper must be removed to enable the RS232C serial interface.
Changing this setting requires the top cover to be removed. Contact customer service
(service@programmablepower.com) to obtain authorization to perform this setting
change.
Figure 3-4: Position of LAN/RS232C selection jumper W2 on 7004-716-2 Range/Relay board.
The RS232C cable required to connect the Lx/Ls Source to a PC serial port is a standard 9 pin
Male to 9 pin Female straight-thorugh serial cable. A suitable 6 feet long RS232C cable is
supplied with each power soruce. (CI P/N 250709). Replacement cables are available through
customer service (service@programmablepower.com)
- Lx \ Ls Series II 1
- AC Power Source 1
- Programming Manual 1
- SAFETY SYMBOLS 7
- Table of Contents 9
- Table of Figures 11
- Table of Tables 11
- 1. Introduction 12
- 1.2.1 Firmware differences 13
- 1.2.2 Hardware differences 13
- 2. Introduction to SCPI 16
- 2.2.3 The SCPI Command Tree 17
- 2.3 Using Queries 19
- 2.4 Coupled Commands 19
- 2.5.3 Headers 20
- 2.5.4 Query Indicator 21
- 2.5.6 Root Specifier 21
- 2.5.7 Message Terminator 21
- 2.6 SCPI Data Formats 22
- 3. System Considerations 24
- 3.2 USB Interface 25
- 3.2.2 USB Interface Use 31
- 3.3 LAN Option 32
- 3.3.5 Socket Port Number 36
- 3.4 RS232C Serial Interface 37
- 4. SCPI Command Reference 39
- 4.2 Subsystem Commands 40
- 4.3 Calibration Subsystem 41
- 4.4 Diagnostic Subsystem 43
- 4.5 Display Subsystem 44
- 4.6 Instrument Subsystem 46
- 4.7 Limit Subsystem 47
- 4.13 Output Subsystem 66
- 4.14 Power On Subsystem 71
- 4.24 System Commands 109
- 4.26 Trigger Subsystem 117
- (default) 118
- 5. Common Commands 122
- 5.1 *CLS 123
- 5.2 *ESR? 123
- 5.3 *IDN? 124
- 5.4 *OPC 124
- 5.5 *OPT? 124
- 5.6 *PSC 124
- 5.7 *RCL 125
- 5.8 *RST 126
- 5.9 *SAV 127
- 5.10 *SRE 127
- 5.11 *STB? 127
- 5.12 *TRG 128
- 5.13 *TST? 128
- 5.14 *WAI 129
- 6. Programming Examples 130
- 6.2.1 Waveform Shapes 132
- 6.2.2 Individual Phases 133
- 6.3 Coupled Commands 134
- FIXED mode 136
- STEP mode 136
- PULSE mode 136
- LIST mode 136
- 6.6 List Transients 138
- INIT[:IMM] 140
- 6.7.7 Generating Triggers 142
- 6.8 Making Measurements 143
- 6.8.2 Power Measurements 144
- 6.8.3 Harmonic Measurements 144
- Offset = 151
- 0 to 2^9 151
- Offset = - 4096 151
- Offset = - 2048 151
- Offset = 0 151
- 6.10.2 Download Sample 152
- 7.1 Power-On Conditions 154
- 7.2 Operation Status Group 154
- 151 155
- 7.6 Status Byte Register 160
- 7.7 Examples 161
- 7.8.1 Remote Inhibit (RI) 164
- 7.9 SCPI Command Completion 165
- 8. Option Commands 166
- 8.2.1 Introduction 167
- 8.2.3 GPIB Address 170
- 8.2.4 APE over RS232 170
- 8.2.5 Message Format 171
- 8.2.6 Numeric Data Field 171
- 8.2.7 Program Headers 172
- 8.2.9 APE Program Headers 174
- 8.2.14 Service Requests 184
- 181 185
- 8.3.1 Introduction 187
- 8.3.2 ABLE Language details 187
- 8.3.3 Language Extension 191
- 8.4 RTCA/DO-160D (-160) 192
- VOLTAGE SURGE, for details 194
- 8.6.1 Command Tree 200
- 8.7.1 Command Tree 207
- 219 223
- 220 224
- 221 225
- 222 226
- SCPI Version 227
- SCPI Confirmed commands 227
- 225 229
- PONS:SYNC[:SOUR] 229
- Appendix C: Error Messages 230
- 227 231
- 228 232
- 229 233
- 230 234
- 231 235
Produits connexes et manuels pour Équipement Ametek Lx Series II Programming Manual
Équipement Ametek MX CTSH Manuel d'utilisateur
(151 pages)
(151 pages)
Équipement Ametek i Series Manuel d'utilisateur
(341 pages)
(341 pages)
Équipement Ametek MX CTSL Manuel d'utilisateur
(157 pages)
(157 pages)
Équipement Ametek PLA-PLW Manuel d'utilisateur
(128 pages)
(128 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels