Ametek ReFlex Firmware Updates Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Ametek ReFlex Firmware Updates. AMETEK ReFlex Firmware Updates User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 8
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Technical Note
ReFlex Power™ Firmware Updates
Document No. M380570-01 Rev B • 1/23/2009
©2008 AMETEK Programmable Power, Inc. • All rights reserved. • AMETEK is a trademark of AMETEK, Inc.
9250 Brown Deer Road, San Diego CA 92121 • Tel: 858-450-0085 • Fax: 858-458-0267 • email: sales@programmablepower.comWeb: www.programmablepower.com
1 of 2
PURPOSE
Provide instructions for updating firmware on all ReFlex Power
TM
modules.
CAUTION
Review this procedure carefully before attempting the update.
BACKGROUND
ReFlex Power
TM
modules, including the ReFlex Power
TM
Controller (RFPC), Low Power DC (LPDC), High Power DC (HPDC),
AC Power Supply (ACPS), Low Power/High Power Active Loads (LPAL/HPAL), and Fixed Power DC (FPDC) contain embedded
firmware in Flash Memory. The release of ReFlex Power
TM
includes periodic pre-planned feature enhancements implemented
through firmware updates.
PROCEDURE
1. On the Internet, go to http://www.programmablepower.com/go/rfp_downloads.
2. In the Software section, click the downloadable for Firmware Update Executable.
3. An RFP Upgrader zip file will pop up; this zip file contains the update Image files, installation programs and instructions.
If the folder is empty, the files may not be available; contact the AMETEK Customer Care Department at
[email protected] to receive the files.
4. Save this zip and extract the contents to an appropriate location on your computer.
5. Follow the instruction documents carefully.
U
PDATE IMAGE FILES
The update Image files contain two types of files “.rbf” and “.bin” files. Below are typical names of the image files. The names
define the type of module, the destination partition and firmware version. The Destination partition defines where the files will be
physically loaded in firmware during the update.
DC:
FPGA Image A: DC_FPGA1_2_000_000.rbf
This is the DC module Field Programmable Gate Array Image 1 version 2.000.000.
FPGA Image B: DC_FPGA2_2_000_000.rbf
This is the DC module Field Programmable Gate Array Image 2, version 2.000.000.
Vue de la page 0
1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Technical Note

Technical Note ReFlex Power™ Firmware Updates Document No. M380570-01 Rev B • 1/23/2009 ©2008 AMETEK Programmable Power, Inc. • All rights res

Page 2

Technical Note ReFlex Power™ Firmware Updates Document No. M380570-01 Rev B • 1/23/2009 ©2008 AMETEK Programmable Power, Inc. • All rights res

Page 3

Technical Note ReFlex Power™ Firmware Updates Document No. M380570-01 Rev B • 1/23/2009 ©2008 AMETEK Programmable Power, Inc. • All rights res

Page 4

Technical Note ReFlex Power™ Firmware Updates Document No. M380570-01 Rev B • 1/23/2009 ©2008 AMETEK Programmable Power, Inc. • All rights res

Page 5

Technical Note ReFlex Power™ Firmware Updates Document No. M380570-01 Rev B • 1/23/2009 ©2008 AMETEK Programmable Power, Inc. • All rights res

Page 6

Technical Note ReFlex Power™ Firmware Updates Document No. M380570-01 Rev B • 1/23/2009 ©2008 AMETEK Programmable Power, Inc. • All rights res

Page 7

Technical Note ReFlex Power™ Firmware Updates Document No. M380570-01 Rev B • 1/23/2009 ©2008 AMETEK Programmable Power, Inc. • All rights res

Page 8

Technical Note ReFlex Power™ Firmware Updates Document No. M380570-01 Rev B • 1/23/2009 ©2008 AMETEK Programmable Power, Inc. • All rights res

Commentaires sur ces manuels

Pas de commentaire